• Surface Preparation: The surface to be coated must be clean, dry and free from dirt, oily residue, grime, loose oxidation, spores (mildew) or any other surface contaminate that could affect product performance. It is imperative to fully and completely clean the surface, as CRYSTALEEN® adheres by chemical and mechanical bonding and must gain proper contact with the surface.
• Mixing: CRYSTALEEN® is packaged in two separate bottles labeled Stage 1 (Sealant-Glassifier®), and Stage 2 (Curing Solution-Hardener), without exposure to air. Shake Stage 1 (Sealant) vigorously for a minute or two until all white sediment is mixed thoroughly in the solution and in suspension. Stage 2 (Curing Solution) does not need to be shaken. Once both parts are ready, attach the spray trigger to the bottles by puncturing the seal with the down spout of the trigger, then threading the trigger on clockwise until the neck of the trigger is tightly secure to the bottle.

• DIRECTIONS:
  Sealant-Glassifier™: Stage 1
• Wash & Dry surface. Remove wax or sealers with PolyWash®, TopCoat® All-Purpose Cleaner, or 91% Rubbing Alcohol.
• Spray on: In fan-like motions, evenly spray a thin, wet layer of Stage 1 on the surface in a 2’ x 2’ section. Wipe on: Spray or pour Stage 1 into a clean & dry TopCoat® applicator pad until saturated & wet, not dripping, then wipe on surface in a 2’x2’ section.

• Curing Solution-Hardener: Stage 2
• Immediately spray Stage 2 evenly over entire area of Stage 1. Let stand for 15 seconds before buffing. With a clean & dry TopCoat® microfiber towel, buff both parts to a smooth and lustrous shine. Final buff with a clean & DRY TopCoat® microfiber towel. Repeat process until entire vehicle is done.
• For improved shine, durability, & protection, apply multiple layers.
• Evenly use Stage 1 & 2 in application.
• Prep Work: Remove oxidization, scratches, paint marks, water stains, and foreign particles before application.
• Do all prep work, washing, and coating out of sun, in ambient temperature. Do not apply in freezing conditions.

A.Multiple layers will protect against rock chips, Crystaleen is incredibly hard! It will mitigate the rock chips, but won't give you 100% protection until you get several coats.

A. No, Crystaleen is not a slick sealant. It is not designed to be slick. Crystaleen is a permanent glass sealant. Crystaleen will have the same feeling as dragging your hand or fingers down a clean glass window. There will be noticeable drag and no slick feel. That is a good thing!! No slickness does not mean Crystaleen is not permanantly bonded to the surface. You will see the sealant in action when you drive through the rain, you will see its super hydrophobic properties in action!! Remember it is a permanent sealant, not a sealer! Continue to use F11 in conjunction with Crystaleen for that slick feel and even more superior production to your vehicle.

A. It lasts forever! It's an aerospace coating, the backbone of our technology was used on the space shuttle! It will not wear off because it is bonded on a molecular level. Nothing will remove it!

A. Absolutely! Anyone can apply it that can follow directions. Make sure you have cleaned and prepped the surface before applying Crystaleen. You want a raw surface, without any waxes or sealers, so it can chemically bond with the substrate. Start with Stage 1 which is a sealant, aka the glassifier! You'll start on a clean, prepped surface. Use caution not to get the product in your eyes, and make sure you're in a well ventilated area! Apply it out of the sun in ambient temperature for best results. Shake up the Stage 1 bottle so everything mixes together fully. Start by spraying it evenly across a 2 foot by 2 foot section at a time! Before buffing, immediately move to Stage 2, the curing solution. This is what causes the sealant to bond to the surface on a molecular level. Evenly spray Stage 2 over the same section and let it sit 5-10 seconds, then buff if in with a microfiber towel. Go over it again with a second, dry microfiber towel. Make sure to continue shaking stage 1 before applying each time. You don't want the product to dry before you buff it off. We recommend you do two coats out of the gate for maximum results, and there is no waiting period between coats!

A. You will want to prepare the surface by removing water spots, scratches, and oxidation or other imperfections before applying Crystaleen!

A. Yes! You want a raw surface, without any waxes or sealers, so it can chemically bond with the substrate.

A. Make sure you have cleaned and prepped the surface before applying Crystaleen. You want a raw surface, without any waxes or sealers, so it can chemically bond with the substrate. Start with Stage 1 which is a sealant, aka the glassifier! You'll start on a clean, prepped surface. Use caution not to get the product in your eyes, and make sure you're in a well ventilated area! Apply it out of the sun in ambient temperature for best results. Shake up the Stage 1 bottle so everything mixes together fully. Start by spraying it evenly across a 2 foot by 2 foot section at a time! Before buffing, immediately move to Stage 2, the curing solution. This is what causes the sealant to bond to the surface on a molecular level. Evenly spray Stage 2 over the same section and let it sit 5-10 seconds, then buff if in with a microfiber towel. Go over it again with a second, dry microfiber towel. Make sure to continue shaking stage 1 before applying each time. You don't want the product to dry before you buff it off. We recommend you do two coats out of the gate for maximum results, and there is no waiting period between coats!